Search Results

FutureSteelVehicle's (FSV) objective is to develop detailed design concepts for a radically different steel body structure for a compact Battery Electric Vehicle (BEV). It also will identify structure changes to accommodate larger Plug-In Hybrid (PHEV) and Fuel Cell (FCEV) vehicle variants. The presentation will demonstrate seven optimized structural sub-systems that contribute to the program's 35 percent mass reduction goals and meet its safety and life cycle emissions targets. It will explain the advanced design optimization process used and the resulting aggressive steel concepts. Presenter Jody R. Shaw, US Steel

Many manufactures are currently working on solutions to fulfill CARB MY 13 requirements for monitoring of diesel particulate filters using a soot sensor. Europe might follow by introducing new OBD limits with EU6 regulation. In this presentation we show results from a study investigating the monitoring capability of a soot sensor in combination with EU6 emission calibration and the OBD matriculate mass limit as proposed in EC 595/2009. A defective diesel particulate filter (DPF) has been detected on roller test bench and under normal driving conditions on public roads. Calibrating a precise soot model is the key factor for the reliability of the particulate filter diagnosis using a soot sensor. Presenter Thomas Czarnecki, Bosch Engineering GmbH

Hybrid technology has the potential to enable dramatic reductions in greenhouse gases (GHG), such as the California goal of reducing GHG by 80 percent from 1990 levels by 2050. As a result it is expected that hybrid systems will occupy a growing proportion of the market. However, introducing a hybrid system in a vehicle may adversely affect the performance of the engine OBD system in monitoring malfunctions impacting pollutant emissions. For example, a hybrid system that reduces time of the engine in idle or deceleration overrun conditions could make a well-performing engine OBD system noncompliant, by reducing in-use frequency of some OBD monitors below acceptable levels. In this presentation, Ricardo will present a process for evaluating the impact that a hybrid system which has been optimised to minimise GHG emission over a specified drive-cycle will have on the effectiveness of engine OBD monitors.

Watlow and EmiSense Technologies, LLC are commercializing an improved electronic particulate matter (PM) sensor that has real-time measurement capability and improved sensitivity. To demonstrate the capability of this improved sensor of on board diagnostics (OBD) for failure detection of diesel particle filters (DPF), independent measurements were performed by university of California Riverside (UCR) and by Southwest Research Institute (SwRI) to characterize the engine PM emissions and to compare with the PM sensor response. In situ PM measurements from PM sensors correlate well with real-time gravimetric measurements. In addition, particle size and particle number data are presented and discussed.Due to an improved design update, the sensitivity of the sensor could have been significantly increased.

Powertrain Systems development is facing unprecedented challenges driven by the convergence of many factors: increasing government regulations for tailpipe emissions, diagnostics and fuel economy, increased competition, shorter development cycles, and tighter program budgets. Using telematics and information technology to automate the evaluation of a system�s robustness enables engineers to focus their time on problem areas during their normal development process and launch with quality. This presentation will use real world examples to detail how this methodology was jointly applied by Control-Tec and Ford Motor Company to identify and improve the system performance of Ford�s Air-Fuel Imbalance Monitor before production. Presenter Bill Leisenring, Control-Tec LLC

Plug-In Hybrid and Extended Range Electric Vehicle's have quickly become the focus of many OEM's and suppliers. Existing regulations and test procedures did not anticipate this rapid adoption of this new technology, resulting in many product development challenges. The lack of clear requirements is further complicated by CARBs consideration of CO2 inclusion in their next light duty OBD regulation. This presentation provides an overview of the regulatory requirements for OBD systems on hybrid vehicles that intend to certify in California. Near term challenges for EREV?s and PHEV?s are discussed, including concerns with the existing denominator and warm-up cycle calculations. Some proposals are made to address these concerns. Presenter Andrew Zettel, General Motors Company

OBD requirements for aftertreatment system components require monitoring of the individual system components. One such component can be an NH3-SCR catalyst for NOx reduction. An OBD method that has been suggested is to generate positive or negative spikes in the inlet NH3 concentration, and monitor the outlet NOx transient response. A slow response indicates that the catalyst is maintaining its NH3 storage capacity, and therefore it is probably not degraded. A fast response indicates the catalyst has lost NH3 storage capacity, and may be degraded. The purpose of the work performed at Southwest Research Institute was to assess this approach for feasibility, effectiveness and practicality. The presentation will describe the work performed, results obtained, and implications for applying this method in test laboratory and real-world situations. Presenter Gordon J. Bartley, Southwest Research Institute

Some the OBD-II regulations have been around for a long time or seem to be intuitively obvious. It is easy to assume to assume that everyone knows how to implement them correctly, that is, until someone actually reads the words and tries to do it. Most often, these issues come up when modifying existing OBD features, not when creating completely new ones. This presentation contains a few examples of features that should have been easy to implement, but turned out not to be easy or simple. Presenter Paul Algis Baltusis, Ford Motor Co.

Sensing exhaust gas temperature is a key component in diesel after treatment systems for both control and diagnostics. Accuracy varies significantly depending upon the sensing technology and implementation in the system. Prior published work has demonstrated that resistance based temperature sensors are not able to achieve the system accuracy required for advanced diagnostics over the life of the emission system. This presentation will show that it is feasible to achieve better than �10�C end of life system accuracy by means of active thermocouple technology. Results from tests at Michigan Technological University will be used to illustrate diagnostic uncertainty related to the application of temperature sensors and a specific DOC/DPF example will be used to show the benefits of accurate temperature based diagnostics. Presenter D. P. Culbertson, Watlow Gordon

A combination of laboratory reactor measurements and vehicle FTP testing has been combined to demonstrate a method for diagnosing the formation of NO2 from a diesel oxidation catalyst (DOC). Using small cores from a production DOC and simulated diesel exhaust, the laboratory reactor experiments are used to support a model for DOC chemical reaction kinetics. The model we propose shows that the ability to produce NO2 is chemically linked to the ability of the catalyst to oxidize hydrocarbon (HC). For thermally damaged DOCs, loss of the HC oxidation function is simultaneous with loss of the NO2 production function. Since HC oxidation is the source of heat generated in the DOC under regeneration conditions, we conclude that a diagnostic of the DOC exotherm is able to detect the failure of the DOC to produce NO2. Vehicle emissions data from a 6.6 L Duramax HD pick-up with DOC of various levels of thermal degradation is provided to support the diagnostic concept.

Revisions to the California OBD-II diesel regulations required many updates to various SAE and ISO on-board diagnostic standards; these include major revisions to SAE J1979, J1699-3, J2012 and J1930. This presentation is intended to review the background for these changes as well as the revisions made in these documents. Presenter Robert Gruszczynski, Volkswagen of America

The OBD approval process can be a frustrating time for both manufacturer and ARB staff. For manufacturers, a long approval process can sometimes mean accepting deficiencies prematurely in exchange for an approval. For ARB staff, they are inundated with highly technical information which they must review, garner understanding of and then apply their experience to evaluate it for compliance. OBD approval anxiety can be minimized, if not avoided, when manufacturers understand ARB�s expectations. This presentation will take you through some unwritten rules and common pitfalls which can impede the approval process, thus providing a guideline to a less painful and more efficient certification document review and approval. Presenter Mark Frank, Winterpark Engineering Llc

Need for worldwide harmonization of regulations. Presenter James Vondale, Ford Motor Co.

Update on light-duty regulations. Presenter Michael J. McCarthy, California Air Resources Board

Software content within commercial vehicles is growing exponentially. Emissions requirements, multiplexed communications, hybrid-electric technologies, active suspensions and smart sensors are amongst the technologies driving the increase in embedded code. Presenter Christoph Braeuchle , MKS Software, Inc.

Concerned with fuel consumption and emissions, especially public transportation in urban areas, the ELFA electric drive system has been developed for hybrid bus applications. This modular system provides bus manufactures a cost effective solution with a maximum degree of design flexibility. Presenter Joshua Nelke, siemens industry inc.

EGR coolers are used in combustion engines to reduce NOx emissions. However, heat transfer in these coolers also results in thermophoresis-temperature-gradient driven motion of suspended particles towards cooler regions-which leads to significant soot deposition. Presenter Meisam Mehravaran

Developing relatively cheap and widely available resources for heterogeneous solid catalyst synthesis is a promising approach for biodiesel fuel industry. Seashell which is essentially calcium carbonate can be used as a basic support for transesterification heterogeneous catalysts. In the present investigation, the alcoholysis of waste frying oil has been carried out using seashell-supported K3 PO4 as solid catalyst. Presenter Essam Oun Al-Zaini, PhD student, UNSW

Architecting and integrating commercial hybrid electric vehicles (HEV) is a long and labor intensive process which is unique every time. The challenge intensifies when one attempts to create an HEV capable of engine-off operation. Presenter Benjamin Saltsman, Eaton Corp.

Hybrid systems have been available for several years now, and offer customers a decrease in fuel consumption and CO2 emissions at an incremental price. Hybrids, in some cases, have offered improved other customer benefits such as reduced noise, vibration and harshness or better acceleration and the satisfaction of increased societal benefit. Sometimes the vehicle utility is compromised by the volume dedicated to energy storage systems. Several hybrid architecture arrangements exist in the market, and offer various levels of hybrid feature. But considering acquisition cost and operating expense, most hybrid vehicles have not offered a direct total cost advantage when compared to non-hybrids. GM's new e-Assist system is highly integrated with the engine and transmission functionality, and takes advantage of the highest value fuel economy enablers available with light electrification.